How To Clear Codes With Cobb Accessport V3

The Cobb Accessport V3 is a handheld device that allows you to clear codes and reset the ECU on your Subaru. It also allows you to datalog, read gauges, and access other features. The V3 can be used on all Subarus from 2008-present.

How To Clear Codes With Cobb Accessport V3

The Cobb Accessport V3 is a handheld device that can be used to clear engine codes on many different makes and models of vehicles. The device plugs into the vehicle’s diagnostic port and retrieves any codes that are stored in the engine’s computer. The codes can then be cleared by pressing a button on the Accessport V3.

1. cobb accessport v3 2. laptop with internet connection 3. obd2 scanner

  • open the cobb accessport v3 application. 2. connect the accessport to your vehicle. 3. select “vehicles & maps” from the main menu. 4. choose the car you want to work on

1. Make sure your accessport is updated to the latest firmware. 2. Enter the Accessport Manager 3. Select “Clear Codes” 4. Select the appropriate vehicle 5. Select “OK”


Frequently Asked Questions

Can You Reprogram A Cobb Accessport?

Yes, you can reprogram a Cobb Accessport. The Cobb Accessport is a handheld device that can be used to modify the engine management system of many cars. It can be reprogrammed to change the settings of the car, such as the fuel mixture, timing, and boost pressure.

How Do I Flash My Cobb Accessport?

To flash your Cobb Accessport, you will need to connect your Accessport to your computer. Next, open the Cobb Install Manager and select your car model. From there, follow the on-screen instructions to install the latest firmware on your Accessport.

How Do I Reset My Cobb Accessport V3?

To reset your Cobb Accessport v3, you will need to unplug the battery for a few minutes. Once the battery is unplugged, you can replug it back in and hold down the button on the back of the unit until you see the green light start flashing.

How Do I Reset My Cobb Tune?

If you are using Cobb’s Accessport, to reset the tune, you will need to go into the AP Manager and click on “Restore Stock.”

How Do You Flash A Cobb Accessport?

To flash a Cobb Accessport, you will need to use the Cobb Flash software. First, make sure you have the latest version of the Cobb Flash software installed on your computer. Next, connect your Accessport to your computer using the USB cable. Once it is connected, open the Cobb Flash software and select your Accessport from the list of devices. Click “Load File” and select the firmware file that you want to install. Once the firmware file is loaded, click “Flash Device.”

How Do I Unmarry My Accessport V3?

To unmarry your Accessport v3, you will need to remove the marriage certificate from the device.

Does Uninstalling Accessport Remove Tune?

No, uninstalling Accessport will not remove the tune.

What Does Reflash Mean On Cobb Accessport?

Reflash means to overwrite the original firmware on a device with new firmware.

How Do You Reset A Cobb Accessport V3?

The Cobb Accessport V3 can be reset by holding the button on the back of the unit for 10 seconds.

How Much Does It Cost To Reset A Cobb Accessport?

It costs $595 to reset a Cobb Accessport.

Can You Unmarry An Accessport Yourself?

Yes, you can unmarry an accessport yourself. To do so, you will need to remove the accessport from your car and unplug the battery. Next, remove the screws that hold the accessport in place and then remove the cover. Finally, unplug the connector and re-install the screws and cover.

How Do I Reset My Ecu Accessport?

The ECU Accessport can be reset by holding the two buttons on the side of the device for about 10 seconds.


Wrap-Up

The Cobb Accessport V3 is an easy-to-use device that allows you to clear engine codes and reset the check engine light on your car.

Leave a Comment